Advice Please

S2SAP
S2SAP Forum Participant Posts: 75
edited April 2018 in Caravans #1

Advice please. When connecting the electric hook up cable / socket to the caravan socket beside the battery it is very stiff / tight pushing it on and pulling it off - my hands have cuts all over them from this. Anyone any useful tips for making the connection easier - I have attached photo to help explain. I tried lubricating it with Mr Sheen but no good.
 

EHU.JPG 82.3K

Comments

  • Cornersteady
    Cornersteady Club Member Posts: 14,623
    5,000 Likes 1000 Comments Name Dropper Photogenic
    edited April 2018 #2

    you could try spraying the blue with WD40? is it a new van?

    Is it stiff because the two parts don't match up in a perfect straight line?

    Try holding the plug in a different manner? ie pull up the flap align loosely then hold where the hinge is?

  • hitchglitch
    hitchglitch Forum Participant Posts: 3,007
    1000 Comments
    edited April 2018 #3

    WD40 for the pins and silicon grease for the plastic contact area.

  • Unknown
    Unknown
    edited April 2018 #4
    This content has been removed.
  • Cornersteady
    Cornersteady Club Member Posts: 14,623
    5,000 Likes 1000 Comments Name Dropper Photogenic
    edited April 2018 #5

    yes  I've never seen sockets like that inside/next to the battery box, indeed a separate compartment for the EHU? 

  • EmilysDad
    EmilysDad Forum Participant Posts: 8,973
    1000 Comments
    edited April 2018 #6

    ive got satellite & telly aerial sockets in my battery compartment along with the 240v connection

    I think there's a 12 volt ciggy lighter type socket too, but can't remember embarassed

  • Cornersteady
    Cornersteady Club Member Posts: 14,623
    5,000 Likes 1000 Comments Name Dropper Photogenic
    edited April 2018 #7

    none of that fancy stuff for ussmile 

    we just have the mover isolation socket but it can't be used if the EHU is in and the EHU can't be used if the isolation key is in (as designed)

  • Unknown
    Unknown
    edited April 2018 #8
    This content has been removed.
  • Unknown
    Unknown Forum Participant
    edited April 2018 #9
    The user and all related content has been Deleted User
  • EasyT
    EasyT Forum Participant Posts: 16,194
    1000 Comments
    edited April 2018 #10

    Makes sense to me. I use silicon grease on waterl plug-in as it tended to stick on previous 'van

  • Simon100
    Simon100 Club Member Posts: 668
    500 Comments 100 Likes
    edited April 2018 #11

    All my Lunars have had satellite connections in the same housing as the ehu socket, as in the picture. I have never had a problem plugging the satellite cable in with the ehu cable in place.

  • lornalou1
    lornalou1 Forum Participant Posts: 2,169
    1000 Comments
    edited April 2018 #12

    get some fine emery paper and rub round the male connector to remove a little of the plastic then lubricate with silicon grease.

  • Nuggy
    Nuggy Forum Participant Posts: 512
    edited April 2018 #13

    I keep a pair of thin cotton gloves for situations like that, the material can absorb any knocks, not your skin or knuckles.

  • S2SAP
    S2SAP Forum Participant Posts: 75
    edited April 2018 #14

    Thanks for the replys I sprayed the pins with wd40 and then cleaned it off and its working much better now thanks again

  • Cornersteady
    Cornersteady Club Member Posts: 14,623
    5,000 Likes 1000 Comments Name Dropper Photogenic
    edited April 2018 #15

    Good to know, thanks for posting back btw, a lot don'tsmile

Categories